pvb20 vickers pump pdf
Rating: 4.8 / 5 (4283 votes)
Downloads: 17813
= = = = = CLICK HERE TO DOWNLOAD = = = = =
Piston Pumps&USgpm Variable Thru Shaft, Side Ported, Inline Piston Pumps. TechnicalInformation. PVB(F)*SFWC(M) PVB(F)*SFXC(M) PVB(F)*SFW M-PVBM– M– M– M– M– M– MS MS MS MSPump shafts are designed to be installed in flexible Eaton’s Vickers® PVH high flow, high performance pumps are a family of variable displace-ment, inline piston units that incorporate the proven design, quality Service Data. Design Code B. Up to barcc/rev (in3/rev) Variable Speed Drive Ready. Vickers®. Axial Piston Pumps. Vickers® byDanfoss. These pumps should not be operated with a vacuum greater thaninches at the inlet or a housing pressure greater thanpsi, unless specifically approved by Vickers engineering. To assist initial priming, manual adjustment control setting must be at least% of maximum flow position. Maximum flow position occurs when rod is fully extendedRetaining Ring Retaining Ring Foot Bracket Mounting Kit FB-C includes Screws (2 req’d) Bearing Option for all sizes except PVB Pressure adjustment range: PVBto bar (to psi) All other sizes: (to bar (to psi) CVP = Load sensing with pressure limiterControl location. Fixed and Variable Displacement. These are Vickers PVB series, variable volume, compensator controlled, piston pumps. PFB 5, PFB, PFBPVB 5/6, PVB/15, PVB/29, PVBand PVBto SAE PVB 5/6, Pump Design Number Control CCompensator control CGRemote adjustment CRDi˛erential cuto˛ CVLoad sensingMobile Application Model Series PVBPump, Vickers®. M-PVB Design. by Danfossused for manual adjustment of pump output flow. Piston Pumps. Revised/01/ MS. WARNING. PVB5 tomodels with “H”, “M” or “V” controls only: L = Left hand, when viewed at shaft end AOperatingData PressureandSpeedLimits Basicmodel Geometric Maximumshaft Maximumoutlet designation dispalcement, speed(r/min) pressure,bar(psi) cm 3/r(in/r) Anti-wear Water-in– Water Anti–wear Water Water-in– AOperating Data Minimum Inlet Pressure (cont’d) 0,,,,,,,,8 psi barAbsolute pressureSupercharge pressure 0,,,0 bar recommended value and cause cavitation in the pump. Piston Pumps. These are model series PVB VICKERS® Service Data isPVB20/RH or LH Shaft Rotation On PVB5/6/10/& PVEmodels, if the shaft rotation is changed from that shown above, theCurrent Vickers by Danfoss. NOTE No application factor is more important to the success of a pump than the inlet line. PFB 5, PFB, PFBPVB 5/6, PVB/15,PVB/29,PVB Vickers®. Considering Pump Design Number Control CCompensator control CGRemote adjustment CRDi˛erential cuto˛ CVLoad sensingMobile Application Model Series PVBPump, variable displacement, in–line piston unit Flow Rating @ RPMUSGPM Mounting FFoot bracket (Omit for ˜ange) Rotation (Viewed from shaft end) RRight hand LLeft Revised/01/MS Variable Inline Piston Pump M-PVB Design M-PVB Design Service Data Vickers® Piston Pumps Eaton Hydraulics, Incorporated Pumps Vickers, Incorporated Service Parts Information M-PVBM-PVBDesign Revised MS Crooks Road Troy, Michigan WARNING PVB20/*-SFXC** F3 Seal Kit for PVB20/*-SFWC** CAUTION Plug Screw (4 req’d) Torque to lb. Replace your old Vickers PVB with the Continental HPV range of piston pumps. M-PVB Design. PVM Variable Displacement Piston Pump. Fixed and Variable Displacement. Variable Inline Piston Pump. in. PistonPumps. Output flow sizes are equal to the Vickers pumps including the 6,,,andgallons per minute @ RPM units. Included in Std Seal Kit for PVB20/*-SFWC**-1* Included in Std Seal Direct Equivalent. Contact us with your Vickers PVB part number for a direct Continental hydraulics replacement pump Axial Piston Pumps. CAUTION Position compensator gasket with small end of teardrop hole point-ing in direction of compensator adjusting plug. Use this drawing for SlideVICKERS PVB SERIES PISTON PUMPS.
留言列表
